Intelligent vehicle model identification via VIN 3. No need the cables contact with Car , More Convenience 4.Pay for one Car brand software can enjoy. Supported Language :English/German/ Spanish/ French/ Italian/ Japanese/ Portuguese. Auto VIN Scan identify Vehicle. Read the current version information of the car ECU. Help you quickly identify the cause of the vehicle breakdown.
Serves to clear the DTC of the ECU memory of the tested system. Help you read and display real-time data and parameters of the car ECU , learn the vehicle's performance and offer maintenance suggestions. Test whether the execution components in the electronic control system can work normally. Keep all previous records on the screen no need to start anew. Thinkcar thinktool Mini Car Diagnostic Tablet is the.Covering more than 94 car brands. It's design for car repair garage, car beauty service parlors, auto mechanic and DIY car owners Highest-Level Auto scanner. Diagnostics cover all vehicles that support the OBD protocol after 1996. Thinktool Mini OBD2 Scanner support All systems Diagnoses, All OBD-II functions, 28 Reset All OBD-II functions. Besides, Also Supported ECU Coding /Action Test and other Special Function. Thinktool mini Supported 28 Kinds of Reset Service. 1 Oil Reset The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle. 3 Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle. 4 Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done. 5 ABS Bleeding When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. Lf the ABS computer, ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS. 6 Break-pad Reset lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.
After replacing the brake pad, you must reset the brake pad. 8 Gear Learning The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires.
Lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off.After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC'gear not learned is present, gear learning must be performed. 9 IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECu, BCM, or remote control battery is replaced, anti-theft key matching must be performed. 10 Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection. 11 TPMS Reset After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, andtire is replaced for the car with tire pressure monitoring function. 12 Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration. 13 AFS Reset This feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture. 14 A/T Learning This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem.
In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality. 15 Sunroof Initialization This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc. 16 EGR Adaption This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.17 ODO Reset a ODo reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. BUsually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance. 18 Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable, it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use.
19 Transport Mode ln order to reduce power consumption, the following functions may be disabled, including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal. 20 A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 21 Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware). 22 NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust.
Lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu. 23 AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required. 24 Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired. 25 Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. 26 Tyre Reset This function is used to set the size parameters of the modified or replaced tire.27 Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window. 28 Language Change This function is used to change the system language of the vehicle central control panel. Full 10 Mode OBDII/EOBD/JOBD Car Diagnostics Functions. Thinktool Mini supports all 10 test modes for OBD-II cars which are great for daily repair work.
The table below describes the purpose of each mode of operation: Reading Codes Show the detailed description of the Diagnostic Trouble Code (DTCs). Show the detailed description of the Diagnostic Trouble Code (DTCs). Turns off Check Engine Light (MIL), clears codes and resets monitors.
Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data. Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing. Show the information of continuous data stream from a vehicle in live graphic (waveform) display. Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs. Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer.
Retrieves and displays test results for emission-related powertrain components and systems. Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.Certain vehicle components can be actuated by commands sent from the scanner to test their operability. Thinktool Mini Support Car models. How to Register Thinktool mini. Turn on the Machine 3. Display Screen 5.99-Inch/TFT(IPS) Connection :Wi-Fi/Bluetooth RAM: 2G ROM:16G Working Temperature: 32122 Storage Temperature: -4144. Here we list some common questions and answers related to this tool. Q: Why does it have no responses when connected to a car computer? A: Check whether the connection with the vehicle diagnostic socket is normal, whether the ignition switch is on, and whether the tool supports the car. Q: Why does the system stop while reading the data stream?
A: This may be caused by loose diagnostic dongles. Please unplug the dongle and reconnect it firmly.Q:Communication error with vehicle ECU? Whether diagnostic dongle is correctly connected. Whether ignition switch is ON. If all checks are normal, send vehicle year, make, model and VIN number to us using Feedback feature.
Q: Why does the host screen flash when the engine ignition starts? A: It is normal and caused by electromagnetic interference. Q: How to upgrade the system software?
Start the tool and ensure a stable Internet connection. Complete the process by following the instructions on the screen step by step.
It may take a few minutes depending on the internet speed. After successfully completing the upgrade, the tool will automatically restart and enter the main interface. Q: Please explain the account and points. A: To use thinktool mini, you need to register an account.
1 point can be deducted for 1 dollar when purchasing products or services Q: How to capture the screenshot? A: A"Screenshot" icon is always floating on the screen. Tap it to capture the current screen and the screenshot is saved in the Think File module. Thinkcar thinktool mini Packing List. 1Thinkcar thinktool Mini Host 1Diagnostic dongle 1Charging cable 1power adapter.Please return the item within. After receiving if you are not happy with your purchasing. 3 Year free repair for the devices.
If the item has been used, we have the right to decline your claim. We are specialized dealer of On-Board Car Diagnostic tools and automotive electronics. For more than 10 years. We are authorized first class distributor of Launch, Foxwell, Autek, Ancel, Innova, Autophix, Thinkcar, Kzyee brands.
And more brands will be show in our store in near future. We have office and warehouse in US and. We promise to help you solve it asap, and make you feel satisfactory absolutely. M-F: 9:30AM - 18:00PM BST (Beijing Standard Time).
After you received our package you are satisfied with it. We will do the same as soon as we can too. The item "THINKTOOL Mini OBD2 Scanner Auto Diagnostic Tool Code Reader All System IMMO DPF" is in sale since Thursday, September 3, 2020. This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Code Readers & Scanners". The seller is "super-diag" and is located in Houston, Texas.
This item can be shipped to United States.