Bi-Directional Actuation Test (Also known as component activation, FOXWELL GT65 plus pro can be used to turn on and off actuators to determine whether there are problems with sensors and actuator) Matching (Also known as adaptive function, it can adjust the data of the actuator so that the data of the replaced actuator can be accepted and recorded by ECU) Coding & Programming Service GT65 allows for the coding and programming of a replacement control module or changing previously stored incorrect coding as expensive factory tools do. ECU Coding Because every automobile part actuator has a record code in ECU, which is the basis for automobile computer to mobilize their work. When you change a new part, the code changes Read ECU Version Diagnostic system. All System Bidirectional OBD2 Diagnostic Scanner ECU Coding Foxwell GT65 Plus. FOXWELL GT65 Plus Support Full System Diagnostic Tool + 30 Special Functions + ECU Coding +programming function + Actuation Test + Bluetooth/Wifi connection +Free Software + Android 10 OS running on 8-inch HD IPS Touch Screen + 32GB Storage+Multi Languages Supported + Wide Vehicles Coverage.
GT65 allows for the coding and programming of a replacement control module or changing previously stored incorrect coding as expensive factory tools do. For BMW F Chassis ECU Coding & hidden Function. For BMW E Chassis ECU Coding &Hidden Function. For Audi Guide Function & Hidden Function.
For VW ECU Coding & Guide Function & Hidden Function. Apart from the general diagnostic functions, GT65 Plus bi-directional tool provides all enhanced service functions, including Key Fob Programming, Oil Reset, EPB, TPS, TPMS, BRT, DPF, SAS, CVT, Gear Learning and Injector Coding, and all kinds of active tests. Allows you to temporarily activate or control a vehicle system or component for active test, provides accurate data results about troubleshoot and diagnostic problems. With this code reader, electronic components check, such as switches, sensors, relays, actuators are made a simple task. It also allows you to recalibrate, adapt or configure certain components after making repairs or replacements.
(Also known as adaptive function, it can adjust the data of the actuator so that the data of the replaced actuator can be accepted and recorded by ECU). FOXWELL GT65 Tablet Scan Tool allows you to do diagnostics on all electronic systems of your vehicle, such as ABS, SRS, Transmission, EPS, Keyless Access, LKAS Control, Air Conditioning System, etc. By reading codes, freeze frame and real-time live data, you can locate your vehicle problem in a few minutes.For instance: Engines/Auto Transmission/Airbags/Immobilizer/Key Coding/ABS/Cruise Control/Instruments/ Self Leveling Suspension systems/Seats/Doors/Gateway/Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted/Power Steering/Tyre Pressure/Rain Sensors/4WD System/Stabilizer/Intelligent Parking Assist/Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti Theft/Soft Top/Headlamp Leveling/Central Locking/Automatic Clutch/ DPF Reset/ Electric Windows/Plip Pro etc system scan. 30+ Service Reset Special Functions. Foxwell GT65 can program and code the electronic control system of prevailing vehicle models, also perform 30 special functions, including. 1 -Oil Light Reset : The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
3 -Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle. 4 -Battery Matching ;This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity.
Lf the ABS computer, ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS. 6 -Break-pad Reset ; lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires.
Lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC'gear not learned is present, gear learning must be performed.To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECu, BCM, or remote control battery is replaced, anti-theft key matching must be performed. 10- Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection. 11- TPMS Reset After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, andtire is replaced for the car with tire pressure monitoring function. 12- Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration. 13- AFS Reset This feature is used to initialize the adaptive headlamp system.
According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture. 14- A/T Learning This function can complete the gearbox self-learning to improve. 15- Sunroof Initialization This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc. 16- EGR Adaption This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.17 -ODO Reset ODo reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. BUsually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance. 18- Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable, it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use. 19- Transport Mode ln order to reduce power consumption, the following functions may be disabled, including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal.
20- A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 21- Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware).
22- NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. Lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu.
23- AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required. 24- Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired.25- Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. 26- Tyre Reset This function is used to set the size parameters of the modified or replaced tire.
27- Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window. 28- Language Change This function is used to change the system language of the vehicle central control panel.Show the detailed description of the Diagnostic Trouble Code (DTCs). Turns off Check Engine Light (MIL), clears codes and resets monitors. Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data. Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing. Show the information of continuous data stream from a vehicle in live graphic (waveform) display. Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs. Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer. Retrieves and displays test results for emission-related powertrain components and systems. Full System Diagnoses Coverage 10000+ Car Models.
American Coverage from 1996 and newer. For Chrysler, For Ford, For GM, For GMBRAZIL (For Brazilian Market Only).Asian Coverage from 2005 and newer. For Acura, For Daewoo, For Daihatsu, For Honda, For Hyundai, For Hyundai CV, For Infiniti, For Isuzu, For Kia, For Lexus, For Mazda, For Mitsubishi, For Nissan, For Scion, For Ssang Yong, For Subaru, For Suzuki, For Toyota, For Mahindra, For Tata (For India market only).
European Coverage from 2004 and newer. For Abarth, For Alfa-Romeo, For Audi, For Aston Martin, For Bentley, For BMW, For Bugatti, For Citroen, For Dacia, For EU Ford, For Fiat, For Ferrari, For Jaguar, For Lancia, For Land Rover, For Lamborghini, For Maserati, For Maybach, For Mercedes Benz, For Mini, For Opel, For Peugeot, For Renault, For Rolls-royce, For Porsche, For Saab, For Seat, For Skoda, For Smart, For Sprinter, For Vauxhall, For Volvo, For VW, For VW_CV. Chinese Coverage from2008 and newer. For BJ HYUNDAI, For BRILBMW, For DF HONDA, For DYK, For FORD CHINA, For GQ FIAT, For GZ HONDA, For MAZDA CHINA, For SAIC SKODA, For SACI VW, For TOYOTA CHINA, For FAW AUDI, For FAW VW, For DFXK/DFFG, For FOTON. Diagnostic system, vehicle identification code, ASAM/ODX document identification and version, part number, software version, hardware version, hardware part number, system description, system abbreviation, FAZIT identification, code workshop code, long code.
Once a vehicle diagnosis is performed, FOXWELL GT65 plus will record the every detail of the diagnostic process. The History function provides quick access to the tested vehicles and users can resume from the last operation, without the necessity of starting from scratch. Data Stream record and playback.
My Report can view Comprehensive diagnostic reports, Remote diagnostic reports, Datastream playback. Record and playback the data stream help you analyze the trouble when driving and solve it. GT65 Plus obd2 scanner shows live vehicle sensors data of all controlled modules in both text and graph formats. Taking advantage of multiple graphing live data, any suspicious or symptom-specific data parameters are more easily to be focused on.
Auxiliary Features Adding Extra Value. Equipped with 7 HD touchscreen with 4000mAh built-in rechargeable battery, driven by 4-core processor and Android system, GT65 diagnostic scanner is capable of doing vehicle auto scanning in just seconds. Meanwhile with intuitive menu for quick navigation, data logging for later analysis, one touch update via WIFI and free 1-year upgrade, the tool is of great assistance and value to an automotive mechanic. English is Default, you still can choose another one langueges from the following. Korea, Spanish, Portuguese, French, Swedish, English, Dutch, Japanese, Italian, German, RussianHungarian, Slovak, Greek, Chinese, Traditional Chinese.If you need other language, please send me the SN Number when you receive it (please register account and activation the sn number first), I will help you change it. NO-IP Limited Update & 2 years free update. You also can do get help by the Diag-Feedback Menu. You also can get 2 years free update, unlike others only 1 year update. Foxwell GT60 Features and Benefits. · Features a 7 TFT Capacitive LCD Touchscreen that will respond to glove use. · User-friendly menu lets you quickly navigate through to find what you need to get the vehicle fixed. · Support multiple vehicle makes. · Compatible with the latest 2019/2020/2021 OBD2 car models, more and more new car models is updating. · Identifies car quickly and easily with automatic VIN reading. · Auto Scan function scans vehicle systems in just seconds.
· Reads and clears diagnostic trouble codes and resets MILs. · Views live vehicle sensors data in text, graph and gauge formats. · Merges interactive live sensor graphs for easy and intuitive diagnosis. · Live data self learning and alarm when live data over range. · Records and playbacks your data logs for off-vehicle review and analysis.
· Supports the most commonly required service features like brake deactivation, service resets BCM/SIR setup, and transmission adaptations. · Unique Logging feature allows for quicker and more accurate fixes for your diagnostic troubles and bugs.
· Instant support available from our technical team by TeamViewer remote control. · One touch update via WIFI makes the scanner keep the latest system status at all times. · Offers excellent shop management capability by keeping customer information and test records. · Scan VIN allows identify ingavehicleby scanning the VIN plateof the vehicle, barcode, QR code or photore cognition. Screen: 8diagonal, daylight readable color LCD screen.
Processor: MT8168 (12nm ARM COTES 4 64bit, 2.0GHz). Dimensions:10.71" 6.42" 1.54 (LWH).Due to any unexpected factor. Understanding would be highly appreciated! Please do not hesitate to leave us your posit. If you are happy with your shopping. We are eager to be your professional parner of automobile diagnostic tool. The item "All System Bidirectional OBD2 Diagnostic Scanner ECU Coding Foxwell GT65 Plus" is in sale since Friday, December 6, 2019. This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Code Readers & Scanners". The seller is "ancel-tool" and is located in Rowland Heights, California.
This item can be shipped to United States, Canada.