XTOOL D7 is a full system diagnostic scanner that can quickly test every system modules status and make faster diagnosis & maintenance via reading/clearing codes as well as viewing live data etc. But only costs you a few minutes to finish full scanning. You can learn to perform complex diagnostic functions with that will give you a lot more power over the ins and outs of your car to figure out what is going on with your modern computerized vehicle, so that you can get it fixed and get back on the road in due time. XTOOL D7 Auto VIN OBD2 Scanner All System Diagnostic IMMO Key Programmer EPB ABS.Is a full system diagnostic scanner that can quickly test every system modules status and make faster diagnosis & maintenance via reading/clearing codes as well as viewing live data etc. For Engine System: Diagnostic tool XTOOL D7 can help detect the engine ignition, fuel injection, air and fuel ratio, and exhaust emission conditions in Engine system to enhance vehicle performance, save energy and reduce exhaust emission. For Transmission: It makes great sense in the safety driving when your car is slipping or difficult to shift, this diagnostic tool can figure the problems out via reading codes in the Transmission system, or check the health status via live data viewing. For ABS System: Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this diagnostic does for you. For SRS System: SRS, safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic tool can detect every electronic parameter to check its health status.
To diagnose Brake System: if you feel the brake pedal is mushy and notice unusual odor or noise, etc. A properly operating brake system is critical to ensure safe vehicle control and operation. To diagnose Emission System: if the system is affected by vehicle age or poor quality fuel.
A good emission system reduces harmful gases to a large degree and protects you from being fined. To diagnose Fuel system: if vehicle won't start or "Check Engine" light is illuminated.
Check car's fuel system regularly ensures the best performance of your car with the lowest emissions. To diagnose Transmission: if your car is slipping or difficult to shift. The system plays an important part in the overall performance of your car.
To diagnose Wiper System: if you observe chattering or streaking wiper. If the car is not regularly checked, the accident might happen because you can't see clearly. 10:To diagnose Light System: if you see rapid signal blinking or dimming lights. As an advanced diagnostic tool, XTOOL D7 has all kinds of services accessible for complete diagnoses and maintenance.You can quickly access to the vehicle systems within this function. You can find commonly used reset functions in the reset menu, and other special functions in the car brand diagnostic softwares menu. The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system. This function has a multitude of usages to maintain the electronic braking system safely and effectively. The applications include deactivating and activating the brake control system, assisting with brake fluid control opening and closing brake pads, and setting brakes after disc or pad replacement, etc. To reset the steering angle, first find the relative zero point position for the car to drive in straight line.
Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. After the engine ECu, crankshaft position sensor, or crankshaft flywheel is replaced, or the DTC'gear not learned' is present, gear learning must be performed.
The BMS (Battery Management System) allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle. When the gearbox is disassembled or repaired (the car battery is powered off), it will cause the shift delay. In this case, you need to perform this operation so that the gearbox can automatically compensate according to the driving situation to achieve better shift quality. This function resets the airbag data to clear the airbag collision fault indicator.This function allows you to quickly look up the tire sensor IDs from the vehicle's ECU, as well as to perform TPMS replacement and sensor test. This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.
This feature is used to initialize the adaptive headlamp system. This function is used to set the size parameters of the modified or replaced tire.
This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. Use this function to activate the electronic water pump before venting the cooling system. XTOOL Newest D7 automotive scanner can actuate solenoids and actuators for active testing, send commands to systems/components to test their working status, without using the vehicle controls. It can read/erase codes, view live data, retrieve ECU info, do active test and service functions for all systems including ECM, TCM, ABS, SRS, BCM, BMS, TPMS, SAS, Fuel System, Light System and A/C system etc.
Auto VIN SCAN for Quick Diagnosis. Once this diagnostic tool and the given car are properly connected, this diagnostic tool XTOOL D7 stars auto-detected process. If needed, you can only view the diagnostic information of the selected systems in the forms of checks. XTOOL D7 Supports 4-in-1 graphic data flow.
4 kinds of Data Dream shows in 1 Graphic , it is better to compare them. Provides very detailed data stream data, it could include the change of Accelerator Pedal Position Sensor1 , Actual Output Shaft Speed , Clutch A Actuator Motor , Vehicle Battery and so on. Graphical data allows you to analyze the data changes of each module more clearly and easily, and it is easier to see the problems in it. Allow you to record the live data stream and view the data of a certain point in a targeted manner.
So that you can view the data more clearly. After you have recorded the data for a period of time, if you want to view and analyze the data just recorded, you need to use data stream playback function to help you. You can view the data at any time you recorded.
Then you can choose " Combine", " Report" and " Record". Will let you share any data status and content you want to display anytime, anywhere. You can send it to your friend or mechanic to help you solve complex problems. Full 10 Mode OBDII/EOBD/JOBD Car Diagnostics Functions. This scanner supports all 10 test modes for OBD-II cars which are great for daily repair work.
The table below describes the purpose of each mode of operation. Show the detailed description of the Diagnostic Trouble Code (DTCs). Turns off Check Engine Light (MIL), clears codes and resets monitors. Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data. Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
Show the information of continuous data stream from a vehicle in live graphic (waveform) display. Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs. Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer. Retrieves and displays test results for emission-related powertrain components and systems.
Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc. Certain vehicle components can be actuated by commands sent from the scanner to test their operability. PIN Code reading with EEPROM. Reads keys from immobilizer's memory. Reset ECM & reset immobilizer.
With full and strong database for the most important vehicle makes. XTOOL D7 can support many kinds of languages: English, Spanish, German, French, Italian, Finnish, Arabic, Japanese, Korean, Polish, Portuguese, Vietnamese, Russian, Simplified Chinese and traditional Chinese. Users can receive a remote support from XTOOL's technical engineers, colleagues, or friends, by allowing them to control this tablet device on their PC via the TeamViewer software. Including How-to Videos, operation skills, and user manual, Q&A, Quick start guide, etc. Once a vehicle diagnosis is performed, XTOOL D7 will record the every detail of the diagnostic process.You can record/review/playback live data anytime. The History function provides quick access to the tested vehicles and users can resume from the last operation, without the necessity of starting from scratch.
Allows you to submit any issues you can't immediately fix. With the support of professional experts, XTOOL will make great efforts to provide you with the best solutions as soon as possible.We'll offer you help, we won't let our buyers suffer any loss. But damage also happens in transit sometimes. This is something we can not control in some cases. We won't let our buyers suffer any loss. Business time: GMT8 (9:00-18:00) from Monday to Friday. We are eager to be your professional partner of automobile diagnostic tool.
We support remote assistance if you have any difficulty in software installation. The item "XTOOL D7 Auto VIN OBD2 Scanner All System Diagnostic IMMO Key Programmer EPB ABS" is in sale since Tuesday, September 28, 2021. This item is in the category "eBay Motors\Automotive Tools & Supplies\Diagnostic Service Tools\Other Diagnostic Service Tools".
The seller is "auto-obdii_store" and is located in Shenzhen. This item can be shipped worldwide.